(THIS IS A "MILLING SERVICE" ONLY, YOU MUST SEND IN THE PARTS TO HAVE THEM MODIFIED. I DO NOT SELL THE PARTS SHOWN ON THE PAGE)

Add Extra Ball Detent $15

This is for AGD ULE Vert feed bodies (Angel threads.)

Does not include detents.

Tack 1 Warpfeed Body Extra Ball Detent Mod $20

Machined to use AGD ULE body detent. Does not include detents.

Drill and Tap ASA for extra port, standard 90* is $15

15* ports are $20

Prices listed are "per hole"

Add a port for a LPR or change sides to route the airline off the other side.

Mill wings off Grip Frame $15 (Any frame)

Customer must strip frame before sending in for machining.

Complete Trigger Mod $15

The "complete trigger mod" includes 2 trigger stops and a sear (arm) mod. (See pictures below)

Never remove an Automag trigger? Click here to learn how.

A ULT is recommended with the Sear mod

This sear mod greatly reduces the distance the trigger has to travel in order to trip the sear.

The trigger stops remove all excess travel that is left over from the sear mod.

To get full benefit from this mod, use a adjustable air system set around 850-900 psi.

Instructions are provided to adjust the trigger according to AGDs recommended specifications.

This is a HIGHLY under rated trigger job, for the money you won't believe the gains.

This mod came about from the research of others on AO. I simply provide the service because it is tricky drilling the sear.

To learn more about this mod click HERE.

Do not send your entire marker for the trigger mod. It is only necessary to send your trigger and sear.

Sear Mod $7.50

2 Trigger Stops $9

AGD Inteli Frame & Y-Grip ULE Milling Service $40

Includes removing center brace.

Your choice of: removing all, part or leaving factory switch bracket.

Milling may vary slightly, this frame was milled to customer specs.

NOTE:

The "inside" of the "back part" of the frame is milled similar to the front (see picture below) but is not pictured.

Mini-Tac-One Milling Service $25

Milling includes cutting down the front and rear of your AGD Tac-One body.

The front is cut down to the length of an AM/MM rail.

The rear is cut down to the factory relief cutout for your air input.

Eye Hole Milling Service for 3mm eyes $40

This service only includes eye hole milling for 3mm eyes.

It does not include eye covers or drilling and tapping for them.

Also, it does not include rail milling to route your wires to the frame.

Complete Eye Milling Service for 3mm Eyes $100

Includes: *Eye hole machining in body *Rail milling to route wires into your frame *Eye cover rail machining and mounting.

NOTE: Eye cover machining is for the covers shown here, you may purchase them from p8ntbal4me on AO.

You must send in your eye covers to get a proper fit.

ULT Valve modification service $30

(This service does not include ULT, testing or final clean up.)

NO warranty or guarantee for ULT mod, buyer assumes all liability. By making the payment for this service, buyer has agreed to the terms of service.

DISCLAIMER :

I do NOT offer ANY warranty or guarantees for the ULT modification service. The nature of the mod lends itself to the possibility of the valve being ruined and unusable for a number of different reasons. Once the damage is done there is no way to fix it. There is no way I can take the job and risk ruining your valve for the price of this service. I will do the machining but you must assume ALL the risks involved in doing this mod. I have done them before and as far as I know I have never ruined one. If you agree to the terms I will gladly accept the job. Sorry, but that is the only way I can take the job.

The machining will fill the chambers with chips. If your power tube tip comes off easy I will clean it out, but sometimes they are difficult to remove. Customer will be responsible for the final cleaning of the valve. Payment for this service indicates you have read and agree to the terms listed above.

Cut down feedtube $15

Please provide the measurements for "how much you want removed."

Grip Frame Dovetail Milling (Any frame) $20

Machining service to add dove tail mount in order to attach ASA directly to the bottom of your frame.

Pump Body Milling (Any AGD body) $30

Pump Rail Milling (Any Non-ULE Rail) $30

Tear Drop Valve Milling $65 (any valve)

I will do additional valves for $40 each (must be same order)

Customer is responsible for stripping down valve before sending in for this mod. Customer will also be responsible for final cleaning before reassembly. I will need the front and back halves of your valve ONLY. Do not send bolt, regulator parts, on-off valve, airline elbow or any additional parts not associated with this service. Thanks.